HEC-RAS Known Issues
Thank you for testing HEC-RAS 6.0 Beta.
Problems with the current beta release (Beta Update 1) of HEC-RAS 6.0 are listed below.
If you are experiencing a problem not listed here and would like to submit a bug report, please email hec.ras@usace.army.mil with a detailed description of the problem.
Beta Update 1 released.
HEC-RAS 6.0 Beta (Update 1)
Issue | Description | Status 1 2 |
---|---|---|
Terrain Modifications | Replace No Values method is not affect the extraction of elevation data for cross sections, elevation-volume curves, cell faces, and profile lines. Use the modifications and set a user-specified elevation as a work-around. | IN PROGRESS |
Terrain Modifications | Some modification methods (Higher, Lower) were not implemented for simple shapes. | IN PROGRESS |
Reach Length Updating | Reach lengths not updating when deleting the immediately downstream cross section. | RESOLVED |
Projection Issue with Gridded Precipitation in HEC-DSS | The reading of gridded data from HEC-DSS was not getting the horizontal coordinate system information correct all the time. In some cases, an older Albers Equal Area projected coordinate system was assumed in order to proceed. This may have caused your precipitation to be shifted away from its true location. | RESOLVED |
Precipitation and Wind Force with 1D Modeling | Using spatial precipitation and wind forces at the same time with 1D river reach modeling. This was fixed for the 1D Finite Difference method, but is still an issue for the 1D Finite Volume solution methodology. | IN PROGRESS |
Mapping Storage Areas - Steady Flow | Storage Areas are not mapped for steady-flow simulations (water surface elevations are not written to the output HDF). | RESOLVED |
Vertical Varying n Values for 1D Cross Sections | If a cross section has vertical varying Manning's n value data and then edited in RAS Mapper, the vertical varying Manning's n value data is lost. | IN PROGRESS |
Bulking Factor Not included in Rating Curves | The bulking factor used for debris flows is not being included in flow rating curves for 1D and 2D modeling. | IN PROGRESS |
Reference Points Not Plotting in Hydrograph Plotter | Reference points are not plotting. | RESOLVED |
1D Sediment Plotter Improvements | We made the following updates to the 1D sediment plotter:
| RESOLVED |
1D sediment plotter crashes with some unsteady files | The cross section sediment plot crashed with some unsteady data sets in the new sediment plotter. | RESOLVED |
Quasi-Unsteady DSS Selection | The initial 6.0 release cannot open a new DSS file or run with a DSS7 file in the quasi-unsteady flow editor. | RESOLVED |
Sediment DSS Selection | The sediment time series DSS option does not open a new file and cannot run with a DSS 7 file in the initial 6.0 release | IN PROGRESS |
Terrain Modifications - Simple Shapes | Extraction of elevation data for Terrain Modifications using simple shapes (circles, rectangles) was not extracting the elevations for the entire shape (levee and channel modifications are working). | RESOLVED |
Plotting From Unsteady Flow Boundary condition Tables | We are moving to a new hydrograph plotting capability. Several of the Boundary Condition Options in the Unsteady Flow Data editor will not allow the user to plot the data. This is a known issue and will be fixed before the final HEC-RAS 6.0 Release. | IN PROGRESS |
3D Viewer - Controller Not Working | Game controller not working in the 3D Viewer. | RESOLVED |
Spatial Precipitation on Storage areas with no 1D Reaches, not functioning. | If a user has storage areas and/or 2D Flow Areas, but no 1D River Reach, the spatial precipitation model run will get an "Access" error right at the beginning of the Unsteady flow analysis. This has been fixed already and will be in the next Beta release. | RESOLVED |
Modified Puls Routing in conjunction with 1D Finite Volume solver. | It was never intended to have the Modified Puls routing option work with the new 1D Finite Volume solver. The modified Puls routing option was added to HEC-RAS due to issues/problems using the current 1D Finite Difference solver in very steep terrain and for very low flows. We will add a data check to the interface to tell users that they cannot use Modified Puls routing option with the 1D Finite volume option. Given that the 1D Finite volume solver can handle dry channels, very low flows, and very steep terrain, users should not need Modified Puls routing when using the 1D Finite Volume solver. | RESOLVED |
2D Bridge Modeling with Pier Debris Option turned on. | The option to use Debris on bridge piers currently does not function within the 2D Bridge modeling approach. We will be making this functional for a future Beta release. | RESOLVED |
Raster Calculator Variable Names | The interface allowed for numeric values for the first character in the Raster Calculator variable names. This caused the script compiler to fail. The interface should not allow input of improper names. | RESOLVED |
2D Bridge Modeling in Metric Units | For 2D bridge data sets in metric units, there is a bug in double converting the bridge curves from English to Metric units. The first time you run it the minimum elevation for the curves is wrong. This is due to the fact that the bridge cross sections are not being converted to English units properly. The second issue is if you rerun the data set with no changes, the entire curves get converted again. So every time you rerun the curves they get lowered by a factor of 3.28. | RESOLVED |
Map Generation - Multiple Maps | A dialog pops up providing a completion message when a map is completed. With multiple maps being generated this stops the creation of consecutive result maps. | RESOLVED |
RAS Mapper - Map Generation | Generation of the Energy (Elevation), Energy (Depth), Froude Map Types results in a map creation failure for the Maximum profile. "Error Generating stored map: all cells were NoData" message is displayed. | RESOLVED |
3D Viewer - Splash Screen Stuck on "Initializing Input" | Sometimes the 3D Viewer splash screen will be stuck on "Initializing Input". To make this not happen, make sure the splash screen has focus from Windows before it reaches "Initializing Input". You can give the window focus by clicking on it. | RESOLVED |
3D Viewer - Z Scaling Missing or Invalid | If the user ever tried setting the Z Scaling to a decimal number in the 3D Viewer Options, they may not be able to start the 3D Viewer from HEC-RAS. To reset the Z Scaling back to an integer, open Ras3DViewer.exe in the installation directory and change the Z Scaling value there. (Z Scaling was intended to work with decimal numbers.) | RESOLVED |
RASter Calculator - Terrain with Spaces in Name | Terrain names that have spaces were not properly recognized in the RASter Calculator. Terrain names must be renamed without spaces or special characters. | RESOLVED |
Culverts on SA/2D Connections | Culverts created on SA/2D Connections in RAS Mapper are not being properly saved. Attempting to access the Culvert Editor in the Geometric Schematic will result in "Run-time error '9'" and crash HEC-RAS. Creating culverts from the Geometric Schematic works properly. | RESOLVED |
Pump Stations - Delete | The user is not able to Delete Pump Stations from RAS Mapper. Deleting the Pump Station from within the Geometric Schematic appears to delete the object, however, it will show up in RAS Mapper. | RESOLVED |
Pump Stations - Highest Elevation in Pump Line | The "Highest elevation in pump line" information is reset to an empty value if the Geometry is edited in RAS Mapper. The value must be re-entered in the Pump Station Editor form the Geometric Schematic. | RESOLVED |
Flow-Roughness and Seasonal Roughness in Unsteady Sediment | There was a bug in the flow- and seasonal- roughness features in HEC-RAS when running unsteady sediment. | RESOLVED |
GDAL Conflict when Opening RAS Mapper | "Error initializing the GDAL path variables. Please check HEC-RAS installation" error message is displayed when attempting to open RAS Mapper. | View Discussion |
1 RESOLVED issues are fixed and will be available in the next release.
2 IN PROGRESS issues are currently being worked on.